|Filter Medium Material||Coniferous Long Fiber Wood Pulp Paper|
The Kleenoil "high pressure" oil filter can be fitted on the "by pass" basis to hydraulic systems, compressors, or any system with oil at pressure up to 3000psi. The flow through the Kleenoil filter is controlled to approx. 4ltrs per minute at 40psi. A flow rate which is low enough to have negligible effect on most "system pressures", yet high enough to ensure that oil is being kept in "as - new" condition.
More than 70% of Hydraulic Failures are caused by contaminants in the oil
Removes contaminant particles down to less than 0.5 microns -
Removes water content from oil to less than 0.25% up to capacity of cartridges
Prevents corrosion of components
Reduces component wear (seals, piston rods, pumps etc.)
Extends life of in-line OEM filters and components.
End to the need to change hydraulic fluids
All properties of oil being cleaned are maintained
Filter cartridge can be changed within minutes.
Can easily be removed and re-installed on replacement equipment
Can be used with virtually any petroleum/synthetic based oil
Used in transport and industry world-wide
The Kleenoil Hydraulic Block is mounted to the bottom of the Kleenoil Bypass Filtration System to convert the lower pressure bypass engine oil filter to a high pressure hydraulic fluid filter.
There are three ports on the valve block as listed:
- Port 1: Low Pressure output approximately 50 PSI normally is blanked off but may be used to supply another filter housing
- Port 2: High pressure input up to 3000 PSI
- Port 3: Return to hydraulic reservoir. This port is fitted with adaptors size No. 6 JIC and it is important that the return hose is of at least 3/8" bore
|Filter Unit Code||HDU 9778||KU65||SDU 9788|
|Filter Cartridge Code||HDC 1878||KF65||SDU 1888|
|Suitable for tanks||Upto 500 ltrs||Upto 1000 ltrs||Upto 1500 ltrs|
|Water retention (down to<0.05%)||0.56ltrs||0.95ltrs||1.2ltrs|
|Technical Specs of Unit (mm)||H 165 Dia 150||H 165 Dia 180||H 165 Dia 220|
|Technical Specs of Catridge (mm)||H 105 Dia 145||H 105 Dia 175||H 105 Dia 200|
Kleenoil By-pass Filter is an additional oil filter fitted in a by-pass route on an engine or machine without making any alteration to the existing system. It is capable to retain contaminant particles, carbon, wear metals down to under 1 micron and totally absorbs water.
It maintains the oil within its operating specifications therefore its life is increased resulting in savings in oil cost. The Kleenoil By-Pass Filter works by taking a percentage of the oil flow and filtering abrasive contaminants such as carbon, wear metals, silicon etc. down to less than one micron and totally removes water.
Extends oil life by upto 5 to 6 times.
Removes moisture, most acids and sulpher dioxides from the oil.
Removes carbon down to approximately 3 microns; Is easy to install.
Extends engine life by at least 2 times.
Reduces engine and machinery components wear; Reduces pollution.
Dramatically reduces engine downtime.
Comes complete with fitting kit.
|Filter Unit Code||SDU 9788||KU65||HDU 9778||LDU 9768|
|Filter Cartridge Code||SDC 1888||KF65||HDC1878||LDC 1868|
|Suitable for Engine Capacity upto||80 ltrs||40 ltrs||40 ltrs||16 ltrs|
|Water retention (down to<0.05%)||1.2ltrs||0.95 ltrs||0.56ltrs||0.32ltrs|
|Technical Specs of Unit||H 165 mm Dia 220 mm||H 180 mm Dia 240 mm||H 165mm Dia 190 mm||H 160 Dia 120mm|
|Technical Specs of Catridge||H 105 mm Dia 200 mm||H 105 mm Dia 175 mm||H 105 mm Dia 145 mm||H 105 mm Dia 104 mm|